 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 1 0.3 mm pitch, 1.2 mm above the board, top and bottom contact, back-flip actuator flexible printed circuit zif connectors fh39 series features 1. low-profile 0.3mm pitch connector with top and bottom contact usable via either its top or bottom contact point, this connector achieves enhanced freedom in terms of the product design. 2. high contact reliability thanks to the spring terminal structure because both top and bottom contact points are spring- loaded, the contact point adapts to the fpc motion, and high contact reliability is ensured. 3. delivered with the actuator open fpc can be immediately inserted without the need for the opening of the actuator. 4. easy fpc insertion entry chamfers at all sides of the fpc insertion slot assure correct insertion and positioning of the fpc. 5. accepts standard fpc thickness 0.2mm thick standard flexible printed circuit (fpc) can be used. this is the only ultra-low profile zif connector using standard fpc. 6. conductive traces on the pcb can run under the connector no exposed contacts on the bottom of the connector. 7. board placement with automatic equipment flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. standard reel packaging contains 5000 connectors. 8. halogen-free * (fh39j series) *as defined by iec61249-2-21 br-900ppm maximum, cl-900ppm maximum, cl + br combined-1,500ppm maximum 2010.9 small size (39 pos. shown) easy fpc insertion completely locked fpc fpc actuator actuator 3.45mm 1.1mm 13.9mm(39 pos.) new t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n .
fh39 series0.3 mm pitch, 1.2 mm above the board, top and bottom contact, back-flip actuator flexible printed circuit zif connectors 2 specifications recommended fpc thickness: 0.2 0.03 mm, gold plated contact pads ordering information fh 39 j - 51s - 0.3 shw ( 10 ) series name:fh series no.:39 blank :standard a :long actuator type j :halogen-free requirements (flame retardance ul94v-0). 1 2 1 3 2 5 7 4 6 3 contact pitch:0.3mm number of positions fh39 :25 to 61 fh39a :67, (71 under planning) fh39j :25 to 51 4 termination type shw...smt horizontal staggered row mount type plating specifications (10)...gold plating with nickel barrier 7 6 storage temperature range storage humidity range -10 to +50c (note 2) relative humidity 90% max. (no condensation) ratings current rating voltage rating 0.2 a 30 vrms ac operating temperature range operating humidity range -55 to +85c (note 1) relative humidity 90% max. (no condensation) note 1: includes temperature rise caused by current flow. note 2: the term "storage" refers to products stored for a long period prior to mounting and use. the operating temperature and humidity range covers the non-conducting condition of installed connectors in storage, shipment or during transportation after board mounting. note 3: information contained in this catalog represents general requirements for this series. contact us for the drawings and specifications for a specific part number shown. item specification conditions 1.insulation resistance 2.withstanding voltage 3.contact resistance 4.durability 5.vibration 6.shock 7.humidity (steady state) 8.temperature cycle 9.resistance to soldering heat 50 m? min. no flashover or insulation breakdown 100 m? max. * including fpc and ffc conductor resistance contact resistance: 100 m? max. no damage, cracks, or parts dislocation no electrical discontinuity of 1s or longer contact resistance: 100 m ? max. no damage, cracks, or parts dislocation no electrical discontinuity of 1s or longer contact resistance: 100 m ? max. no damage, cracks, or parts dislocation contact resistance: 100 m? max. insulation resistance: 50 m? min. no damage, cracks, or parts dislocation contact resistance: 100 m? max. insulation resistance: 50 m? min. no damage, cracks, or parts dislocation no deformation of components affecting performance 100 v dc 90 vrms ac / 1 minute 1 ma, ac max (ac: 1khz) 10 cycles frequency: 10 to 55 hz, single amplitude of 0.75 mm, 10 cycles in each of the 3 axis acceleration of 981m/s 2 , 6 ms duration, sine half-wave, 3 cycles in each of the 3 axis 96 hours at 40? and humidity of 90 to 95% temperature:-55? ?+15? to +35??+85??+15? to +35? time: 30? 2 to 3 ? 30? 2 to 3 minutes 5 cycles reflow: at the recommended temperature profile manual soldering: 350? 5? for 5 seconds part material finish remarks insulator lcp color:beige ul94v-0 pa color:black contacts phosphor bronze gold plated ----------------- metalfittings pure tin reflow plated ----------------- materials 5 t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 3 fh39 series0.3 mm pitch, 1.2 mm above the board, top and bottom contact, back-flip actuator flexible printed circuit zif connectors connector dimensions all dimensions: mm tape and reel packaging (5,000 pieces/reel). order by number of reels. part number fh39-25s-0.3shw(10) fh39-27s-0.3shw(10) fh39-29s-0.3shw(10) fh39-33s-0.3shw(10) fh39-39s-0.3shw(10) fh39-45s-0.3shw(10) fh39-51s-0.3shw(10) fh39-61s-0.3shw(10) fh39a-67s-0.3shw(10) fh39a-71s-0.3shw(10) fh39j-25s-0.3shw(10) fh39j-33s-0.3shw(10) fh39j-39s-0.3shw(10) fh39j-45s-0.3shw(10) fh39j-51s-0.3shw(10) 580-1806-8-10 580-1805-5-10 580-1807-0-10 580-1803-0-10 580-1800-1-10 580-1802-7-10 580-1801-4-10 580-1808-3-10 580-1809-6-10 under planning 580-1815-9-10 580-1814-6-10 580-1813-3-10 580-1811-8-10 580-1812-0-10 25 27 29 33 39 45 51 61 67 71 25 33 39 45 51 9.7 10.3 10.9 12.1 13.9 15.7 17.5 20.5 22.3 23.5 9.7 12.1 13.9 15.7 17.5 6.6 7.2 7.8 9 10.8 12.6 14.4 17.4 19.2 20.4 6.6 9 10.8 12.6 14.4 7.2 7.8 8.4 9.6 11.4 13.2 15 18 19.8 21 7.2 9.6 11.4 13.2 15 7.83 8.43 9.03 10.23 12.03 13.83 15.63 18.63 20.43 21.63 7.83 10.23 12.03 13.83 15.63 9.15 9.75 10.35 11.55 13.35 15.15 16.95 19.95 21.75 22.95 9.15 11.55 13.35 15.15 16.95 cl no. number of contacts a b c d e note 1 : the coplanarity of each terminal lead within specified dimension is 0.1 mm max. 2 : packaged on tape and reel only. check packaging specification. 3 : slight variations in color of the plastic compounds do not affect form, fit or function of the connector. 4 : after reflow, the terminal plating may change color, however this does not represent a quality issue. a0.15 b0.1 0.60.1 0.30.1 (0.12) c0.1 0.60.1 3.550.2 (1.85) (0.12) (d) (0.15) e0.1 (0.6) (3.3) production lot no. b 0.1 0.1 1 1 (90?) (3.85) (0.85) (1.55) (2.1) 0.470.1 0.10.15 3.250.15 0.10.15 0.30.1 (0.42) (fpc:t0.2mm) 1.10.1 (1.54) b detailed drawing [fh39 series] (90?) (4.15) (0.85) (1.55) (2.1) 0.470.1 0.10.15 3.250.15 0.10.15 0.30.1 (0.42) (fpc:t0.2mm) 1.10.1 (1.89) 0.1 0.1 b detailed drawing [fh39a series] 1 1 t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . fh39 series0.3 mm pitch, 1.2 mm above the board, top and bottom contact, back-flip actuator flexible printed circuit zif connectors 4 b0.05 0.60.05 0.30.03 c0.05 0.30.03 0.60.05 0.80.05 0.350.05 (3.65) 0.670.05 0.50.05 (metal mask:0.42) (metal mask:0.57) 0.10.05 10.05 0.30.05 (0.2) (0.1) 2.480.05 (metal mask:0.25) (metal mask:0.25) (metal mask:0.35) (metal mask:1) recommended metal mask thickness : t=0.1 2-r0.2 f0.05 c0.03 0.60.02 0.30.02 0.30.07 0.30.07 0.3 0.1 0.2 b0.03 0.60.07 0.60.07 0.30.1 1.050.1 1.150.1 2.10.1 2.250.1 2.650.3 3.65min (stiffner) 0.20.03 0.10.02 +0.04 -0.03 0.3 +0.04 -0.03 (uncovered area) recommended pcb mounting pattern and metal mask dimensions recommended fpc dimensions all dimensions: mm part number fh39-25s-0.3shw(10) fh39-27s-0.3shw(10) fh39-29s-0.3shw(10) fh39-33s-0.3shw(10) fh39-39s-0.3shw(10) fh39-45s-0.3shw(10) fh39-51s-0.3shw(10) fh39-61s-0.3shw(10) fh39a-67s-0.3shw(10) fh39a-71s-0.3shw(10) fh39j-25s-0.3shw(10) fh39j-33s-0.3shw(10) fh39j-39s-0.3shw(10) fh39j-45s-0.3shw(10) fh39j-51s-0.3shw(10) 580-1806-8-10 580-1805-5-10 580-1807-0-10 580-1803-0-10 580-1800-1-10 580-1802-7-10 580-1801-4-10 580-1808-3-10 580-1809-6-10 under planning 580-1815-9-10 580-1814-6-10 580-1813-3-10 580-1811-8-10 580-1812-0-10 25 27 29 33 39 45 51 61 67 71 25 33 39 45 51 6.6 7.2 7.8 9 10.8 12.6 14.4 17.4 19.2 20.4 6.6 9 10.8 12.6 14.4 cl no. number of contacts b 7.2 7.8 8.4 9.6 11.4 13.2 15 18 19.8 21 7.2 9.6 11.4 13.2 15 c 7.8 8.4 9 10.2 12 13.8 15.6 18.6 20.4 21.6 7.8 10.2 12 13.8 15.6 f * stiffener dimension should be 3.65mm min., and x dimension should be 0.5mm for improved flexibility of fpc. t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 5 fh39 series0.3 mm pitch, 1.2 mm above the board, top and bottom contact, back-flip actuator flexible printed circuit zif connectors recommended fpc construction 1. using single-sided fpc fpc : flexible printed circuit material name surface treatment copper foil base adhesive base film reinforcement material adhesive stiffener material material thickness (m) cu 1oz thermosetting adhesive polyimide 1 mil thick thermosetting adhesive polyimide 3 mil thick total 0.2m thick gold plated over 1 to 5 m nickel underplating covering film layer cover adhesive polyimide 1 mil thick. 3 35 25 25 40 75 203 ( 25 ) ( 25 ) copper foil cover adhesive covering film layer reinforcement material adhesive stiffener 2. using double-sided fpc fpc : flexible printed circuit covering film layer cover adhesive surface treatment through-hole copper copper foil base adhesive base film base adhesive cu 1/2oz thermosetting adhesive polyimide 1 mil thick. thermosetting adhesive polyimide 3 mil thick total ( 18 ) 25 25 25 25 197 polyimide 1 mil thick. cu cu 1/2oz thermosetting adhesive polyimide 1 mil thick thermosetting adhesive ( 25 ) ( 25 ) 3 15 18 18 25 18 material name material material thickness (m) * to prevent release of the fpc due to its bending, use of the double sided fpc with copper foil on the back side is not recommended. 1: this specification is a recommendation for the construction of the fh39 series fpc (t=0.20.05). 2: for details about the construction, please contact the fpc manufacturers. 3. precautions 0.2m thick gold plated over 1 to 5 m nickel underplating t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . fh39 series0.3 mm pitch, 1.2 mm above the board, top and bottom contact, back-flip actuator flexible printed circuit zif connectors 6 packaging specification embossed carrier tape dimensions (tape width 32mm min.) reel dimensions embossed carrier tape dimensions (tape width to 24mm max.) ?1.5 (2.1:fh39 series) (0.3) 80.1 20.15 40.1 (4.65) g0.3 j0.1 (k) h0.1 g0.3 j0.1 1.750.1 1.750.1 (1.85) 1.7 1.5 (2.4:fh39a series) (k) unreeling direction flat surface, for placement with automatic equipment. +0.15 0 +0.1 0 +0.1 0 ?1.5 +0.1 0 (?13) (?380) (?80) (l: inside) (m: outside) t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 7 fh39 series0.3 mm pitch, 1.2 mm above the board, top and bottom contact, back-flip actuator flexible printed circuit zif connectors all dimensions: mm tape and reel packaging (5,000 pieces/reel). part number fh39-25s-0.3shw(10) fh39-27s-0.3shw(10) fh39-29s-0.3shw(10) fh39-33s-0.3shw(10) fh39-39s-0.3shw(10) fh39-45s-0.3shw(10) fh39-51s-0.3shw(10) fh39-61s-0.3shw(10) fh39a-67s-0.3shw(10) fh39a-71s-0.3shw(10) fh39j-25s-0.3shw(10) fh39j-33s-0.3shw(10) fh39j-39s-0.3shw(10) fh39j-45s-0.3shw(10) fh39j-51s-0.3shw(10) 580-1806-8-10 580-1805-5-10 580-1807-0-10 580-1803-0-10 580-1800-1-10 580-1802-7-10 580-1801-4-10 580-1808-3-10 580-1809-6-10 under planning 580-1815-9-10 580-1814-6-10 580-1813-3-10 580-1811-8-10 580-1812-0-10 25 27 29 33 39 45 51 61 67 71 25 33 39 45 51 24 24 24 24 24 32 32 44 44 44 24 24 24 32 32 cl no. number of contacts g --- --- --- --- --- 28.4 28.4 40.4 40.4 40.4 --- --- --- 28.4 28.4 h 11.5 11.5 11.5 11.5 11.5 14.2 14.2 20.2 20.2 20.2 11.5 11.5 11.5 14.2 14.2 j 11 11.6 12.2 13.4 15.2 17 18.8 21.8 23.6 24.8 11 13.4 15.2 17 18.8 k 25.4 25.4 25.4 25.4 25.4 33.4 33.4 45.4 45.4 45.4 25.4 25.4 25.4 33.4 33.4 l 29.4 29.4 29.4 29.4 29.4 37.4 37.4 49.4 49.4 49.4 29.4 29.4 29.4 37.4 37.4 m t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . fh39 series0.3 mm pitch, 1.2 mm above the board, top and bottom contact, back-flip actuator flexible printed circuit zif connectors 8 temperature profile hrs test condition solder method :reflow, ir/hot air environment :room air solder composition :paste, 96.5%sn/3.0%ag/0.5%cu (senju metal industry, co., ltd.'s part number:m705-221cm5-32-10.5) test board :glass epoxy 25mm50mm0.8mm thick land dimensions :0.3mm0.5mm, 0.3mm0.67mm metal mask :0.250.42, 0.250.570.1mm thick the temperature profiles shown are based on the above conditions. in individual applications the actual temperature may vary, depending on solder paste type, volume / thickness and board size / thickness. consult your solder paste and equipment manufacturer for specific recommendations. start (?) temperature 0 50 100 150 200 250 max 250? time (seconds) 25? (60sec.) (60sec.) 90 sec. to 120 sec. preheating soldering 150? 200? 230? t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . fh39 series0.3 mm pitch, 1.2 mm above the board, top and bottom contact, back-flip actuator flexible printed circuit zif connectors 9 connector operation and precautions operation 1. as delivered exercise care when handling connectors. follow recommendations given below. delivered with the actuator open. there is no need to operate the actuator prior to the insertion of the fpc. 2. fpc insertion align the fpc perpendicular with the connector and insert it firmly all the way. the actuator is open when delivered in the embossed tape packaging the actuator is open when delivered in the embossed tape packaging t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . rotate rotate excessive force after the actuator is already closed excessive force after the actuator is already closed excessive force after the actuator is already closed push at the center of the actuator. push at the center of the actuator. do not close at the ends. do not close at the ends. rotate (lift) rotate (lift) do not attempt to open more than 90 do not attempt to open more than 90 lift at the center lift at the center do not open (lift) at one end. do not open (lift) at one end. operation 3. locking after fpc/ffc insertion, rotate the actuator down to a full stop, pushing it at the center. 4. fpc removal (lock release) carefully rotate the actuator up to 90? lifting it at the center. * the actuator opens by rotating it in the direction opposite to the direction of the insertion of the fpc. do not attempt to open it from the same side as the insertion of the fpc. fh39 series0.3 mm pitch, 1.2 mm above the board, top and bottom contact, back-flip actuator flexible printed circuit zif connectors 10 t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 11 fh39 series0.3 mm pitch, 1.2 mm above the board, top and bottom contact, back-flip actuator flexible printed circuit zif connectors precautions when mounting connectors on the pcb other precautions when hand soldering: do not perform hand soldering with the fpc inserted in the connector. ?do not apply excessive heat or touch the soldering iron anywhere other than the connector leads. ?do not use excessive amount of solder or flux compounds. operation of the actuator or contacts may be affected by excessive amounts of solder or flux compounds. handling before mounting on pcb insertion of the fpc or operation of the actuator prior to mounting on the pcb is not recommended. pc board warpage minimize the warpage as much as possible. the connector is straight within 0.1 mm max. make sure that the mounting area flatness can accept the connector terminals without causing any failure of the solder joints. forces on the board when braking the large pc board into individual boards exercise care not to damage the installed connectors. when attaching the boards or other components with the screws make sure that any stresses will not cause board deflections affecting the mounting areas of the connector. connector pcb t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . |
Price & Availability of FH39-27S-03SHW
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |